9/9

LATHE INSERTS

In stock
WNMG060404 HQ CA5525 (STEEL)
NZ$9.40
Fine to medium machining of steel.    Kyocera Japan. WNMG060404 HQ CA5525 (0.4mm...
In stock
CCMT060202 PP (STAINLESS & STEEL)
NZ$7.50
CCMT060202 PP   Finishing. 0.2mm Nose radius.  Fine machining of stainless steel and steel. ...
In stock
MGMN400-M 4mm Groove Insert 5 Pack
NZ$72.00
MGMN400-MG 4mm Groove Insert Suitable for steel, stainless steel and cast iron. Suits MGIVR internal...
In stock
WCMT06T308-MM 10 Pack
NZ$84.00
     WCMT06T308-MM-CX31NS U-Drill insert. Suites U Drills 31~42mm Go...
In stock
DCGT070202-FA-CU1000 (NON FERROUS)
NZ$8.20
DCGT070202-FA-CU1000 (0.2mm corner radius) These inserts are high rake with sharp ground edges and...
In stock
MRMN400-MG 4mm Round Groove Insert 5 Pack
NZ$72.00
MRMN400-MG 4mm (2mm radius) Groove Insert Suitable for steel, stainless steel and cast iron. Suits...
In stock
MGGN400-JM 4mm Groove Insert 5 Pack
NZ$45.00
MGGN400-JM 4mm Groove Insert 5 pack. High rake ground insert suitable for steel, stainless steel and non...
In stock
TCMT110208 HQ CA5525
NZ$7.00
TCMT110204 HQ Fine to medium machining of steel. Excellent chip control at low feed and depth of...
In stock
DCGT070204-FA-CU1000 (NON FERROUS)
NZ$8.20
DCGT070204-FA-CU1000 These inserts are high rake with sharp ground edges and polished top surface....
In stock
WNMG060408 HQ CA5525 (STEEL)
NZ$9.40
Fine to medium machining of steel.    Kyocera Japan WNMG060408 HQ CA5525 (0.8mm Corner...
In stock
TPGN110304 PT600M CERAMIC
NZ$19.00
TPGN110304-T00820 PT600M Ceramic insert for hardened steel and high speed machining of cast iron. PT600M...
In stock
CCMT060204 HQ (STEEL)
NZ$7.50
CCMT060204 HQ   0.4 Nose radius. Fine to medium machining of steel. Excellent chip...
In stock
DCMT11T304 MQ CA6525 (STAINLESS & STEEL)
NZ$10.80
DCMT11T304 MQ CA6525 Fine machining of stainless steel and steel. Excellent chip control at low...
In stock
WCMT080412-MM 10 Pack
NZ$84.00
WCMT080412-MM-CX31NS U-Drill insert. Suites U Drills 43~60mm Go to U-Drills
In stock
TPGH080204L PR930
NZ$14.80
TPGH090204L PR930 Grade information. PR930   Tough grade for general machining of stainless steel...
In stock
TPMT090204 HQ (Stainless/Steel)
NZ$7.00
TPMT090204 HQ Recommended grade for general machining of stainless steel and steel. Suits...
In stock
DCMT11T304 HQ CA6525 (STAINLESS & STEEL)
NZ$10.80
DCMT11T304 HQ CA6525 Fine to medium machining of stainless steel and steel. Excellent chip control...
In stock
DCGT11T304-AG (NON FERROUS)
NZ$9.60
DCGT11T304-AG These inserts are high rake with sharp ground edges and polished top surface. Intended for...
In stock
TCMT110204 HQ TN60
NZ$7.00
TCMT110204 HQ TN60 CERMET GRADE Fine machining of steel. Can also take light cuts in hard material....
In stock
CCGT060202MP-CK
NZ$19.00
CCGT060202MP-CK   Finishing. 0.2mm Nose radius. Super precision insert suitable for fine...
In stock
SCMX09T304 Spot Drill Insert
NZ$18.60
SCMX09T304 Spot Drill Insert to fit DTS Spot Drills Inserted Spot drill 10mm shank Inserted...
In stock
TPGN110304 CERAMIC
NZ$19.00
TPGN110304 Ceramic insert for hardened steel and high speed machining of cast iron. Able to withstand light...
In stock
TPGN110308 PT600M CERAMIC
NZ$14.40
TPGN110308 PT600M Coated ceramic insert for hardened steel. Coated ceramic is able to withstand very...
In stock
DCMT11T308 HQ CA6525 (STAINLESS & STEEL)
NZ$10.80
DCMT11T308 HQ CA6525 Fine to medium machining of stainless steel and steel. Excellent chip...
Show another 24 products