9/9

LATHE INSERTS

In stock
WNMG060404 HQ CA5525 (STEEL)
NZ$9.40
Fine to medium machining of steel.    Kyocera Japan. WNMG060404 HQ CA5525 (0.4mm...
In stock
CCMT060202 PP (STAINLESS & STEEL)
NZ$7.50
CCMT060202 PP   Finishing. 0.2mm Nose radius.  Fine machining of stainless steel and steel. ...
In stock
MGMN400-M 4mm Groove Insert 5 Pack
NZ$72.00
MGMN400-MG 4mm Groove Insert Suitable for steel, stainless steel and cast iron. Suits MGIVR internal...
In stock
WCMT06T308-MM 10 Pack
NZ$84.00
     WCMT06T308-MM-CX31NS U-Drill insert. Suites U Drills 31~42mm Go...
In stock
DCGT070202-FA-CU1000 (NON FERROUS)
NZ$8.20
DCGT070202-FA-CU1000 (0.2mm corner radius) These inserts are high rake with sharp ground edges and...
In stock
MRMN400-MG 4mm Round Groove Insert 5 Pack
NZ$72.00
MRMN400-MG 4mm (2mm radius) Groove Insert Suitable for steel, stainless steel and cast iron. Suits...
In stock
MGGN400-JM 4mm Groove Insert 5 Pack
NZ$45.00
MGGN400-JM 4mm Groove Insert 5 pack. High rake ground insert suitable for steel, stainless steel and non...
In stock
TCMT110208 HQ CA5525
NZ$7.00
TCMT110204 HQ Fine to medium machining of steel. Excellent chip control at low feed and depth of...
In stock
DCGT070204-FA-CU1000 (NON FERROUS)
NZ$8.20
DCGT070204-FA-CU1000 These inserts are high rake with sharp ground edges and polished top surface....
In stock
WNMG060408 HQ CA5525 (STEEL)
NZ$9.40
Fine to medium machining of steel.    Kyocera Japan WNMG060408 HQ CA5525 (0.8mm Corner...
In stock
TPGN110304 PT600M CERAMIC
NZ$19.00
TPGN110304-T00820 PT600M Ceramic insert for hardened steel and high speed machining of cast iron. PT600M...
In stock
CCMT060204 HQ (STEEL)
NZ$7.50
CCMT060204 HQ   0.4 Nose radius. Fine to medium machining of steel. Excellent chip...
In stock
DCMT11T304 MQ CA6525 (STAINLESS & STEEL)
NZ$10.80
DCMT11T304 MQ CA6525 Fine machining of stainless steel and steel. Excellent chip control at low...
In stock
WCMT080412-MM 10 Pack
NZ$84.00
WCMT080412-MM-CX31NS U-Drill insert. Suites U Drills 43~60mm Go to U-Drills
In stock
TPGH080204L PR930
NZ$14.80
TPGH090204L PR930 Grade information. PR930   Tough grade for general machining of stainless steel...
In stock
TPMT090204 HQ (Stainless/Steel)
NZ$7.00
TPMT090204 HQ Recommended grade for general machining of stainless steel and steel. Suits...
In stock
DCMT11T304 HQ CA6525 (STAINLESS & STEEL)
NZ$10.80
DCMT11T304 HQ CA6525 Fine to medium machining of stainless steel and steel. Excellent chip control...
In stock
DCGT11T304-AG (NON FERROUS)
NZ$9.60
DCGT11T304-AG These inserts are high rake with sharp ground edges and polished top surface. Intended for...
In stock
TCMT110204 HQ TN60
NZ$7.00
TCMT110204 HQ TN60 CERMET GRADE Fine machining of steel. Can also take light cuts in hard material....
In stock
CCGT060202MP-CK
NZ$19.00
CCGT060202MP-CK   Finishing. 0.2mm Nose radius. Super precision insert suitable for fine...
In stock
SCMX09T304 Spot Drill Insert
NZ$18.60
SCMX09T304 Spot Drill Insert to fit DTS Spot Drills Inserted Spot drill 10mm shank Inserted...
In stock
TPGN110304 CERAMIC
NZ$19.00
TPGN110304 Ceramic insert for hardened steel and high speed machining of cast iron. Able to withstand light...
In stock
TPGN110308 PT600M CERAMIC
NZ$14.40
TPGN110308 PT600M Coated ceramic insert for hardened steel. Coated ceramic is able to withstand very...
In stock
DCMT11T308 HQ CA6525 (STAINLESS & STEEL)
NZ$10.80
DCMT11T308 HQ CA6525 Fine to medium machining of stainless steel and steel. Excellent chip...
In stock
TCMT110204 HQ CA5515
NZ$7.00
TCMT110204 HQCA5515 Fine to medium machining of steel. Excellent chip control at low feed and...
In stock
WNMG080404 GS CA5515 (STEEL)
NZ$9.90
WNMG080404 GS CA5515 Medium to rough machining of steel. Good general use insert with strong edge...
In stock
TPGN160308 PT600M CERAMIC
NZ$18.00
TPGN160308 PT600M Coated ceramic insert Coated ceramic insert for hardened steel. PT600M Coated...
In stock
DCGX11T308-AL (NON FERROUS)
NZ$9.60
DCGX11T308-AL These inserts are high rake with sharp ground edges and polished top surface. Intended for...
In stock
SCGX09T304 Spot Drill Insert Aluminium
NZ$22.00
SCGX09T304 AG-CX10 Spot Drill Insert. Grade and geometry for nonferrous materials. To suit DTS...
In stock
TPMT090204 HQ PR1725 (Steel/stainless)
NZ$7.00
TPMT090204 HQ PR1725 Recommended grade for general machining of stainless steel and steel. Suits...
In stock
CCGT060204L-F
NZ$8.00
CCGT060204L-F   Finishing. 0.4mm Nose radius. Suitable for fine machining of stainless steel, steel...
In stock
RCGT0602M0-AK (NON FERROUS)
NZ$9.60
RCGT0602M0 AL 6mm diameter Suits tools below SRACR1010K06 SRACR1212K06 SRACR1616K06...
In stock
RCGT0803M0 AL (NON FERROUS)
NZ$9.60
RCGT0803M0 AL 8mm diameter Suits tools below   SRACR1212K08 SRACR1616K08 SRACR2020K08...
RCGX1003M0-AQ KW10 (NON FERROUS)
NZ$9.40
Out of stock
RCGX1003M0-AQ KW10 for aluminium and plastic. Sharp ground cutting edge for non ferrous materials. Round...
In stock
SCGT09T304-AL (NON FERROUS)
NZ$8.60
SCGT09T304-AL   0.4mm corner radius Suitable for aluminium, plastic and other soft...
In stock
VCGT160404 AG-CX10 (NON FERROUS)
NZ$13.80
VCGT160404 AG-CX10 These inserts are high rake with sharp ground edges and polished top surface....
In stock
TCGT090204-FA (NON FERROUS)
NZ$9.40
TCGT090204-FA These inserts are high rake with sharp ground edges and polished top surface. Intended...
In stock
WNMG080408 GS CA5515 (STEEL)
NZ$9.90
WNMG080408 GS CA5515 Medium to rough machining of steel. Good general use insert with strong edge...
In stock
TPGN160304 PT600M CERAMIC
NZ$18.00
TPGN160304 PT600M Coated ceramic insert for hardened steel. PT600M Coated ceramic is able to withstand...
In stock
TCMT110208 HQ CA5515
NZ$7.00
TCMT110204 HQ CA5515 Fine to medium machining of steel. Excellent chip control at low feed and...
In stock
DCMT11T304 HQ CA525 (STEEL)
NZ$10.80
DCMT11T304 HQ CA525 Fine to medium machining of steel. Excellent chip control at low feed and...
In stock
TCMX16T308-SM Spot Drill Insert
NZ$21.60
TCMX16T308-SM-CX32HS Spot Drill Insert. Suitable for steel, stainless and general. Fits DTS...
In stock
TPGH090204L
NZ$8.00
TPGH090204L Grade information. Tough grade for general machining of most materials . Fully...
In stock
CCGT060204R-F
NZ$8.00
CCGT060204R-F   Finishing. 0.4mm Nose radius. Suitable for fine machining of stainless steel, steel...
In stock
VCGT160408 AL (NON FERROUS)
NZ$13.80
VCGT160408 AL These inserts are high rake with sharp ground edges and polished top surface. Intended...
In stock
4.0mm EXTERNAL THREAD INSERT 22ER400ISO
NZ$24.00
22ER400ISO 4mm EXTERNAL THREADING INSERT Full profile insert 4mm Pitch. Standard insert fits most...
In stock
WNMG080408 HQ CA6525 (STAINLESS / STEEL)
NZ$9.90
Fine to medium machining of steel.    Kyocera Japan WNMG080408 HQ CA6525 (0.8mm Corner...
In stock
TCGT110204 AG-CX10 (NON FERROUS)
NZ$9.40
TCGT110204 FA-CX10 These inserts are high rake with sharp ground edges and polished top surface....
In stock
T11IR100 INTERNAL GROOVE INSERT 1mm
NZ$13.40
T11IR100 INTERNAL GROOVE INSERT 1mm Suits most brands of threading bar using the small 11mm inserts. Suits...
In stock
DCMT11T308 HQ CA525 (STEEL)
NZ$10.80
DCMT11T308 HQ CA525 Fine to medium machining of stainless steel and steel. Excellent chip...
In stock
TCGX16T308-AG Spot Drill Insert
NZ$25.80
TCGX16T308-AG Spot Drill Insert for non-ferrous. Suitable aluminium, plastics and soft materials....
In stock
DCMT11T304 HQ CA5515 (STEEL)
NZ$10.80
DCMT11T304 HQ CA5515 Fine to medium machining of steel. Excellent chip control at low feed and...
In stock
CCMT09T304 HQ (STAINLESS & STEEL)
NZ$10.50
CCMT09T304 HQ    Fine to medium machining of steel and stainless steel. Excellent...
TPMT110304 HQ (Stainless and Steel)
NZ$8.80
Out of stock
TPMT110304 HQ First recommended grade for general machining of stainless steel and steel. Suits...
In stock
T16IR100 INTERNAL GROOVE INSERT 1mm
NZ$13.40
T16IR100 INTERNAL GROOVE INSERT 1mm Suits most brands of threading bar. If used in Sandvik, centre height...
In stock
TCGT16T304-FA (NON FERROUS)
NZ$12.40
TCGT16T304-FA  (NON FERROUS) These inserts are high rake with sharp ground edges and polished top...
In stock
WNMG080408 PG CA525 (STEEL)
NZ$9.90
WNMG080408 PG CA525 Medium machining of   steel, suitable for intermittent cutting....
In stock
ZXMT11T306GM PR1230 10 Pack
NZ$80.00
ZXMT11T306GM PR1230 U-Drill insert. GM general purpose insert for steel. Suits DRX Drills 32-38mm...
In stock
TCGT110204 FG (Finishing)
NZ$12.90
TCGT110204 FG CX1060 High rake and ground cutting edge for fine machining in most materials....
In stock
TCMT16T304 HQ CA5525
NZ$9.80
TCMT16T304 HQ CA5525 Fine to medium machining of steel. Excellent chip control at low feed and...
In stock
DCMT11T308 HQ CA5515 (STEEL)
NZ$10.80
DCMT11T308 HQ CA5515 Fine to medium machining of steel.  Excellent chip control at low feed and depth...
In stock
CCMT09T304 HQ CA5515 (STEEL)
NZ$10.50
CCMT09T304 HQ CA5515   Fine to medium machining of steel. Excellent chip control at...
In stock
TCGT16T308-FA (NON FERROUS)
NZ$12.40
TCGT16T308-FA These inserts are high rake with sharp ground edges and polished top surface. Intended...
In stock
VBMT160404 HQ CA6525 (Steel/Stainless)
NZ$14.00
VBMT160404 HQ CA6525 Fine to medium machining of steel and stainless. Excellent chip control at low feed...
In stock
TPMT110308 HQ CA6525
NZ$7.00
TPMT110308 HQ CA6525 CA6525 First recommended grade for general machining of stainless steel and...
In stock
T16IR120 INTERNAL GROOVE INSERT 1.2mm
NZ$13.40
T16IR120 INTERNAL GROOVE INSERT 1.2mm Suits most brands of threading bar. If used in Sandvik, centre height...
In stock
ZCMT12T306 PR1025 10 Pack
NZ$128.00
ZCMT12T306 PR1025 U-Drill insert. GM general purpose insert for steel. Suits DRX Drill...
In stock
T16IR150 INTERNAL GROOVE INSERT 1.5mm
NZ$13.40
T16IR150 INTERNAL GROOVE INSERT 1.5mm Suits most brands of threading bar. If used in Sandvik, centre height...
In stock
CCMT09T308 HQ CA525 (STEEL)
NZ$10.50
CCMT09T308 HQ CA525   Medium machining of steel. Excellent chip control at low feed and...
In stock
TCMT16T308 HQ CA5525
NZ$9.80
TCMT16T308 HQ CA5525 Fine to medium machining of steel. Excellent chip control at low feed and...
In stock
CCMT09T308 HQ (STAINLESS & STEEL)
NZ$10.50
CCMT09T308 HQ    Fine to medium machining of stainless steel and steel. Excellent...
In stock
T16ER100 EXTERNAL GROOVE INSERT 1.0mm
NZ$13.40
T16ER100 EXTERNAL GROOVE INSERT 1.0mm Suits most brands of threading tool. If used in Sandvik, centre...
In stock
VBMT160404 HQ CA6515 (Steel/Stainless)
NZ$14.00
VBMT160404 HQ CA6515 Fine to medium machining of steel and stainless. Excellent chip control at low feed...
In stock
WNMG080408 PS CA525 (STEEL)
NZ$9.90
WNMG080408 PS CA525 Medium machining of   steel. General use insert suitable for...
In stock
TPGH110304L
NZ$8.00
TPGH110304L PR930 (0.4 CORNER RADIUS) Grade information. Tough grade for general machining of most...
In stock
TCMT16T312 HQ CA5525
NZ$9.80
TCMT16T312 HQ CA5525 Fine to medium machining of steel. Excellent chip control at low feed and...
In stock
CCMT09T308 HQ CA515 (STEEL)
NZ$10.50
CCMT09T308 HQ CA515   Fine to medium machining of steel. Excellent chip control at low...
In stock
TNGG160404R-A3 KW10 (NON FERROUS)
NZ$11.80
Machining of aluminium and plastic. Kyocera Japan. TNGG160404R-A3 KW10 (0.4mm CORNER RADIUS)...
In stock
T16ER120 EXTERNAL GROOVE INSERT 1.2mm
NZ$13.40
T16ER120 EXTERNAL GROOVE INSERT 1.2mm Suits most brands of threading tool. If used in Sandvik, centre...
In stock
WNMG080404 PS CA6525 (STAINLESS & STEEL)
NZ$9.90
WNMG080404 PS CA6525 Medium machining of stainless steel and steel. Good general use insert...
In stock
TNGG160408R-A3 KW10 (NON FERROUS)
NZ$11.80
  Machining of aluminium and plastic. Kyocera Japan. TNGG160408R-A3 KW10 (0.8mm CORNER RADIUS)...
In stock
TNGG160404L-A3 KW10 (NON FERROUS)
NZ$11.80
  Machining of aluminium and plastic.    Kyocera Japan. TNGG160404L-A3 KW10 (0.4mm...
In stock
TNGG160408L-A3 KW10 (NON FERROUS)
NZ$11.80
Machining of aluminium and plastic.    Kyocera Japan. TNGG160408L-A3 KW10 (0.8mm CORNER...
In stock
WNMG080408 PS CA6525 (STAINLESS & STEEL)
NZ$9.90
WNMG080408 PS CA6525 Medium machining of stainless steel and steel. Good general use insert...
In stock
TCMT16T304 HQ CA5515
NZ$9.80
TCMT16T304 HQ CA5515 Fine to medium machining of steel. Excellent chip control at low feed and...
In stock
VBMT160408 HQ CA6525 (Steel/Stainless)
NZ$14.00
VBMT160408 HQ CA6525 Fine to medium machining of steel and stainless. Excellent chip control at low feed...
In stock
T16ER150 EXTERNAL GROOVE INSERT 1.5mm
NZ$13.40
T16ER150 EXTERNAL GROOVE INSERT 1.5mm Suits most brands of threading tool. If used in Sandvik, centre...
In stock
TNMG160404 AH (NON FERROUS)
NZ$10.00
Roughing aluminium and other soft materials.   Kyocera Japan. TNMG160404 AH (0.4mm CORNER...
In stock
CCMT09T304 PP (Finishing)
NZ$10.50
CCMT09T304 PP PV720  Finishing. 0.4mm Nose radius. Fine machining of steel and stainless...
In stock
DCGW11T304 KW10
NZ$16.00
DCGW11T304 KW10 Suitable for cast iron, great for brake lathes. Suits boring bars...
In stock
TNMG160408 AH (NON FERROUS)
NZ$10.00
Roughing aluminium and other soft materials.   Kyocera Japan. TNMG160408 AH (0.8mm CORNER...
In stock
WNMG080408 PS CA5515 (STEEL)
NZ$9.90
WNMG080408 PS CA5515 Medium machining of   steel. Good general use insert suitable for...
In stock
TCMT16T308 HQ CA5515
NZ$9.80
TCMT16T308 HQ CA5515 Fine to medium machining of steel. Excellent chip control at low feed and...
In stock
TPGH110308L PR930
NZ$14.80
TPGH110308L PR930 (0.8 CORNER RADIUS) Grade information. PR930   Tough grade for general...
In stock
VBMT160408 HQ CA6515 (Steel/Stainless)
NZ$14.00
VBMT160408 HQ CA6515 Fine to medium machining of stainless steel and steel. Excellent chip control at...
In stock
CCGT09T302MP-CK
NZ$19.00
CCGT09T302MP-CK   Finishing. 0.2mm Nose radius. Super precision insert suitable for fine...
Show another 32 products